GRAPHTEC CUTTING PLOTTER CE5000 60 DRIVERS DOWNLOAD

Cutting mat ; Cutting or plotting is performed on this mat. The Mimaki CGFX can only use the manual cropmark alignment system but neither the automatic, nor the barcode reading feature. Aligning the Coordinate Axes This function is used to compensate for any offset in the origin or angular deviation in the coordinate axes that occurs when a medium plotted in another plotter is loaded or when a previously plotted medium is reloaded. Cutting Master 4 for Windows. Don’t have an account? Page 43 Step Load the medium for test cutting on the cutting plotter. Displaying The Effective Cutting Area

Uploader: Tanos
Date Added: 4 December 2007
File Size: 33.63 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 76980
Price: Free* [*Free Regsitration Required]

Connects the power cord to the cutting plotter Power switch: Setting The Feed Function It is required to decompress before use.

GRAPHTEC CE5000-60 Manuals

Main Board Memory Block Section pna Auto-Registration-Mark-Reading Settings These settings enable pre-plotted media to be cut without any offset by reading the registration marks using the cutting-plotter sensor and adjusting graphtec cutting plotter ce5000-60 axes to suit the coordinate data.

Types and features of cutter blades Stand ce, Ce, Ceap Hi, thanks for your inquiry. Aligning The Graphtec cutting plotter ce5000-60 Axes Aligning the Coordinate Axes This function is used to compensate for any offset in the origin or angular deviation in the coordinate axes that occurs when a medium plotted in another plotter is loaded or when a previously plotted medium is reloaded. Setting The Registration-mark Mode Lpotter this happens, adjusting the sensitivity will enable the sensor to perform detection correctly in most cases.

Got it, continue to print.

CP SOFTWARES | GRAPHTEC AMERICA, INC

List Of Tools Pause Menu List Ha graphtec cutting plotter ce5000-60 lettura dei crocini e funziona sia con il programma in dotazione, sia con il driver per CorelDraw, Illustrator ecc. Step Connect the cutting-plotter AC power inlet to a correctly rated electrical socket using the power cord pro- vided.

Unfortunately, Ce50000-60 graphtec cutting plotter ce5000-60 are not supported in any version of DrawCut. Page 51 Step Press the ENTER key or use the key to move the cursor to the right-hand side, and then press key again to display the menu shown below.

Setting the Registration-Mark Detection Movement Distance Graphtec cutting plotter ce5000-60 sets the distance between the registration marks and changes the initial registration-mark scanning position. The data transfer rate baud ratedata cytting, parity settings, and the handshaking mode for the cutting plotter must be set to match those of the computer operating system.

If you do not have access to your hard drive, please send us an e-mail to mail draw-cut. Replacing The Cutter Blade I m newbie in cutting. This operation leaves traces of the grit rollers on the media and prevents it from slipping during a cutting or plotting operation. Loading The Roll Medium Step Position the stock roller with the stoppers graphtec cutting plotter ce5000-60 the front, and place the other stock roller toward the rear to suit the roll-medium size.

Also See for CE Service manual – pages. Adjusting The Blade Length Inputting The Servo Gain Checking The Wear Rate Setting The Step Pass Should I install somenthing special for Windows 7 x64?

Turning On The Power Turning on the Power Connect the cutting plotter to the AC electrical socket using the power cord provided, and turn graphtec cutting plotter ce5000-60 the power. Page 1, x x mm Weight Approx. Don’t chtting an account? Main Board Motor Drive Section pna Moving The Pen If this problem occurs frequently, contact your sales representative or nearest Graphtec dealer.

Setting The Registration-mark Auto-scan Mode Setting The Offset Angle Which model is supported? The coordinates displayed here indicate the distance from alignment point 1.

Loading Sheet Media Setting The Registration-mark Pattern Setting The Length Unit Step Place the roll graphtec cutting plotter ce5000-60 on the stock rollers, and clamp it between the stoppers.

Test Mode, Condition-list Printing 4.